LR-Cal LSP 1000-H
Pressure comparison test pump
Manual test pressure generation 1.000 bar
- Manual spindle pump
- Hydraulic (with oil or water)
- Test pressure generation up to 1,000 bar (14,500 psi)
- Simple generation, precise fine adjustment
Description
LR-Cal LSP 1000-H description
The LR-Cal LSP 1000-H pressure comparison test pump is used to generate pressure for checking, adjusting and calibrating mechanical and electronic pressure measuring instruments of all types by means of comparison measurements. These pressure tests can take place stationary in the laboratory or workshop, but also on site at the measuring point.
If the pressure gauge to be tested and a sufficiently accurate reference pressure gauge are connected to the LR-Cal LSP 1000-H pressure comparison test pump, the same pressure acts on both gauges when the pump is actuated. By comparing the two measured values at any pressure values, it is possible to check the measuring accuracy or adjust the pressure gauge to be tested.
For exact approaching of the measuring points, the pressure comparison test device (spindle pump) LR-Cal LSP 1000-H is equipped with a finely actuated spindle wheel. The device is characterized by a rotating spindle running only inside the pump body, thus eliminating a disadvantageous bending moment on a turned-out spindle and, especially for mobile use, there is also the advantage that the dimension of the pressure comparison test pump does not change during operation by turning the spindle. The LR-Cal LSP 1000-H pressure comparison test device requires only a very small amount of force.
To considerably reduce the risk of contamination of the operating medium, the pump is equipped with protective filters at the pressure connections and in the reservoir bottom. (Note: when operating with oil, the dirt strainer in the reservoir must be removed).
Specification
LR-Cal LSP 1000-H specification
Pressure generation | [bar] | 0...1,000 (14,500 psi) |
Medium | Mineral oil based hydraulic fluids or destilled water | |
Pressure ports | 2 x 1/2" BSP female, rotating (incl. strainers and gaskets) | |
Fluid reservoir | cm³ | 200 (with strainer) |
Piston diameter | [mm] | 8 |
Spindle stroke | [cm³] | approx. 3.9 (per turn approx. 0.1) |
Needed force | [Nm] | at 250 bar: 2.0; at 500 bar: 4.0; at 1,000 bar: 8.0 |
Materials | Stainless steel, aluminium, brass, Plexiglass, ABS, Viton and NBR | |
Distance of pressure ports | [mm] | 181 |
Dimensions | [mm] | D 388 x W 322 x H 167 (without star-handles) |
Weight | [kg] | 10.5 |
Design | Base plate with feet and rigid housing | |
Order-Code | LSP-1000-H |
Versions for aggressive media like SKYDROL or brake fluids also available (Order-Code: LSP-1000-H-S).
When operating with oil instead of water, remove the dirt sieves.
Scope of standard supply
LR-Cal LSP 1000-H scope of standard supply
- Pressure comparison test pump LR-Cal LSP 1000-H with reference device connection 1/2" BSP female (free-running) on top of the pump and with test item connection 1/2" BSP female (free-running) also on top of the pump
- Built-in priming pump
- Dirt strainers in the reservoir bottom and in both pressure ports (to be removed when operating with oil)
- Operating manual DE+EN
LR-Cal LSP 1000-H accessories + spare parts
Hydraulic oil1 liter
Accessory:
Hydraulic fluid based on mineral oil
Bottle with 1 liter content
HAP-02Hand suction pump
Accessories:
Hand suction pump, significantly facilitates the removal of the operating liquid from the pressure comparison test pump.
Blanking plugfor pressure port
Accessory:
Blanking plug 1/2" BSP male, made of stainless steel, for shutting off a pressure connection
Thread adapterfor pressure ports
Accessory:
Stainless steel thread adapter set for pressure connection
- 1/2" BSP M x 1/4" BSP female
- 1/2" BSP M x 1/4" NPT female
- 1/2" BSP M x 1/2" NPT female
- 1/2" BSP M x M20 x 1,5 female
incl. PTFE sealing rings
90° angle adapterfor pressure ports
Accessory:
Angled connection (90°) for test specimens or references with axial pressure connection at the back 1/2" BSP M.
With integrated seal and knurled nut for toolless pressure gauge change
Minimess 1620 adapterfor pressure ports
Accessory:
Coupling
System "MINIMESS® 1620" x 1/2" BSP male
for connection to pressure port
Pressure test hoseMINIMESS 1620
Accessory:
Pressure test hose (max. +70°C)
System "MINIMESS® 1620"
The following lengths are available:
MMS-M16X2-1-0: length 1.0 meter
MMS-M16X2-2-0: length 2.0 meter
MMS-M16X2-3-2: length 3.2 meter
MMS-M16X2-4-0: length 4.0 meter
Gauge screw connectionMINIMESS 1620
Accessory:
MINIMESS® 1620" system
Manometer bulkhead fitting
with 1/4" BSP female thread
Maintenance kit
Spare part:
Maintenance kitwith dirt sieves, O-rings, etc.
The instructions for this maintenance kit are included in the equipment manual.
Locking lever
Spare part:
Assembly
Locking lever
(incl. sealing rings)
LR-Cal LSP 1000-H Training video: Commissioning and application