|
|
High
Pressure Deadweight Tester
 CPB5000-HP
Ranges 20 bar to 5000 bar
290 psi to 60000 psi |
 |
- Ranges from 20 to 2000 bar (290 to 40000 psi), from
20 to 4000 bar (290 to 60000 psi) or from 20 to 5000 bar (290 to 70000
psi)
hydraulic operated
- Accuracy (total uncertainty of measurement) up to
±0.020% of measured value
- Tester with two piston-/cylinder-units and two weight
sets
- High performance spindle pump for easy generation of
high pressure
- Pressure port for test specimen including 3 different
adapters (with sealing cone)
- Options: DKD Certificate of Calibration
Deadweight Tester (Pressure Balances)
are the most accurate instruments for the calibration of electronic or
mechanical pressure measuring instruments. The direct measurement of
pressure, according to its definition as a quotient of force and area, and
the use of high-quality materials result in small uncertainties of
measurement and an excellent long-term stability of five years. For these
reasons, deadweight testers have already been used in calibration
laboratories of industry, national institutes and research labs for many
years.
Due to the integrated pressure generation and the purely
mechanical measurement principle, the
CPB5000-HP deadweight
testers are ideally suited for on-site use as well as service and
maintenance purposes.
The core of the
CPB5000-HP is a piston/cylinder
system of special material. Besides this high-quality material, which
primarily stands out for its small temperature coefficient, the
workmanship of the system is a measure of the final accuracy of the
pressure balance. Several refinement processes ensure a high-quality and
even surface with small graps of only a few micrometer.
In order to generate the individual test points, the piston/cylinder system
is weighted with mass-loads, which are also calibrated and specially adapted
to the respective application. The pressure is set via the integrated pump.
For fine adjustment an adjustable volume with precision spindle is
available. The weight applied is proportional to the desired pressure and
provided by using optimally graduated weights. As soon as the measuring
system reaches quilibrium, there is a balance of forces between pressure and
wheel weights. Due to the excellent quality of the system this pressure
remains stable over several minutes, so that for instance adjustments of
your device under test can be carried out without any problems.
Optional Accessories
- Set of trim-masses for generating intermediate values
(weights 2 mg to 100 g)
- DKD certification (instead of standard factory
certificate of calibration)
Included in Standard Supply
- Basement with adjustable feet and water level
- Priming pressure pump
- High performance spindle pump
- Pressure port for specimens including following
adapters (each with sealing cone):
M16x1.5 and M20x1.5 and 9/16-18 UNF
- piston/cylinder-system
- set of stainless steel weights in carrying case
Technical Data:
Measuring
Range bar |
Measuring
Range psi |
Version |
| 20...2500 |
290...40000 |
Hydraulic
(for special oil - 0.5 or 1 liter included in scope of
delivery) |
|
20...4000 |
290...60000 |
|
20...5000 |
290...70000 |
Accuracy (uncertainty):
±0.025% of measured value (%RD). The accuracy is characterized by the deviation
span, which is the sum of the systematic error and the uncertainties of
measurement. Long-term stability is not taken into account. Please note that
corrections might be required if the instrument is used without the optional
Intelligent Calibration Module - see operating manual.
As an option, systems with increased accuracies up to 0.02% of reading are
available
| Recommended accessory:
Hand Suction Pump HAP 02
Datasheet
for suction of fluids, e.g. oil, water, break fluid, etc.
Perfect for the suction of the operation fluid of deadweight
tester (e.g. before transport etc.). |
|
Other Deadweight Tester models:
-
CPB5000-DP: Differential
Pressure Deadweight tester
-
CPB5000: Deadweight Tester /
Pressure Balances
-
LDW 1000:
Deadweight Tester "Low Cost", Accuracy ±0.025%
|
|
Unsere
Produkte:
